|
|
|
NewPro-Texx High Performance Surface Coating |
- The Heat, Cold, Moisture Protective and Energy-
Saving Coating all in one for Exterior Surfaces |
|
|
Product Description
|
|
NewPro-Texx High Performance Surface Coating is a high-quality paint coating
for exterior surfaces with its 47% content of microscopic small ceramic balls (bubbles).
A few of the essential advantages of these bubbles are their heat, cold and
moisture insulation effects.
|
|
|
Range of Application and Use
|
|
NewPro-Texx offers very good adhesive characteristics and is, therefore, can be
directly applied to very many different surfaces. |
|
This includes particularly the following:
|
|
|
Your Advantages
|
|
Here is an overview of the
essential advantages of NewPro-Texx:
-
A 10-year material guarantee from one of our authorized processing companies
-
Cost savings through reduced energy consumption
-
Easy-to-clean, due to high surface strength
-
Environmentally safe, due to an absence of solvents
-
High opacity/covering power
-
Long-lasting facade protection through an extremely high resistivity against
weathering erosion
-
Maximum optical appearance – stabile color and high brilliancy
-
No embrittlement, due to high UV-resistance
-
Resistance against algae, moss and fungal decay
-
Very low soiling tendency due to a micro-raw ceramic surface.
|
|
|
Product Characteristics
|
|
Thanks to a active
principle of moisture and heat decoupling, a noticeable increase in improvement
of heat insulation characteristics and summer heat protection occurs. As a
result, the heat and energy input can be greatly reduced. Surfaces coated with NewPro-Texx exhibit an above-average durability. |
|
Further characteristics include:
-
Easy application
-
Effective on absorbable- and diffusible surfaces moisture regulating
-
Fast-drying
-
Flame resistant
-
Free of allergy triggering gas emissions and solvent content adhesive agents
-
High color durability
-
High resistance against aggressive environmental influences such as smog and
ozone
-
permanently reflective
-
resistant against UV-rays and wreathing exposure
-
Suitable for airless spray (sprayable)
-
Variabel diffusion
-
very good adhesive characteristics and, therefore, can be directly applied to
very many surfaces.
|
|
Notice:
A heat loss of up to 25% on
masonry can be caused by moisture. Through a fully functional coating of
NewPro-Texx, which protects the external walls against wetness, a great amount
of energy can be saved. |
|
|
Instructions Regarding Use/Application
|
|
Surface Preparation:
On water retentive surfaces, in
which there is a suspicion of an increased residual moisture, after the first
coating with NewPro-Texx it is advisable to wait for any probable water
discharge on the building part surface. If there is a water discharge, any
further coatings should only applied after the moisture dries. This does not
present any defect or deficiency, rather it is the direct result of the effect
of NewPro-Texx.
All surfaces should be free of
rust, grease, dust, and should be dry and sustainable. Chalk surfaces should be
washed. Loose residues (undissolved paints, plaster remains or the like) are to
be completely removed.
|
|
Priming Coats:
For some surfaces, it may be
necessary that a priming coat be applied to the surface prior to the first
coating. It is advisable to apply the primer NewPro-Fix from the NewPro product
range due to the fact that it is exactly designed to compliment and work with
NewPro-Texx High Performance Surface Coating.
It is also possible to use a
standard primer, however it is important to make sure that this product is
absolutely compatible. The primer, in any case, must not be “surface sealing”.
The diffusion readiness in this case must be higher than for NewPro-Texx. High
Performance Coating.
|
|
Mixing
Instructions:
NewPro-Texx
High Performance Surface Coating can be diluted with up to 5% water.
|
|
Application:
NewPro-Texx High Performance Surface Coating is delivered ready to use. It can
be applied using a brush, roll or airless spraying device. NewPro-Texx High
Performance Surface Coating is applied in two stages (two coats).
Between the two coatings,
depending on weather conditions, there should be a 2-3 hour period of drying.
During application and the drying times, the surface and air temperature should
not fall below +5° Celsius.
The complete product
characteristics of NewPro-Texx High Performance Surface Coating typically appear
approximately 36 days after application, as is with coating substances with
similar bonding agents.
|
|
Machine/Mechanical
Application:
NewPro-Texx
High Performance Surface Coating can be applied using a standard airless
spraying device. Please pay careful attention to the manufacturer’s instructions
regarding the use of this device and NewPro’s authorization for the use of this
device.
|
|
Caution:
Because the application of this
product is linked to an UV cross-linked bonding agent, it must be ensured that
there is sufficient daylight-UV-radiation. Before beginning work and after
longer working breaks, the material must be adequately stirred.
NewPro-Texx High Performance
Surface Coating can be used on a wide variety of surfaces. It is still, however,
recommended that the user carry out a test to determine the surface for the
suitability and stability for the intended purpose.
|
|
Use:
This is simply
a recommended standard, which in end effect can vary depending on the layer of
thickness as well as the structure of the surface.
An exact
amount of material needed can only be determined by a sample coating on the
surface of the object. |
|
|
Required Conditions for Use/Application
|
|
The
application and drying must be effectuated with a minimum surface and air
temperature of +5° Celsius.
|
|
Drying Times:
-
the humidity should not exceed 80%
-
by lower temperatures and/or
higher air moisture/humidity, longer drying times are to be expected.
During the drying period, the
coated surface must be protected from rain.
|
|
Cleaning of Tools and Working
Equipment:
After use of an airless-spraying
device, also follow the manufacturer’s cleaning instructions. |
|
|
Form
of Delivery
|
|
Units per Package:
Further bundle sizes are
available on request. |
|
Color:
Please contact us if you have
any questions regarding this or if you would like to have any further
information. |
|
|
Special Notices
|
|
Transport:
|
|
Storage:
|
|
Disposal:
-
Due to the very good environmentally safe biodegradability, the dried material
remains can be disposed of in the domestic refuse (pursuant to the
corresponding local official laws or regulations)
-
Emptied containers or packaging can be recycled.
|
|
|
Work
Hygiene
|
|
Before
breaks and when finished working with the product, wash hands thoroughly.
Do not
eat, drink or smoke during use. Avoid eye and skin contact with the product.
For
further instructions, cautions or notices, please refer to the product safety
data sheets. |
|
|
Safety Precautions
|
|
Keep
away from children. Keep containers sealed tightly closed. In the event of eye
contact, immediately flush eyes out with a lot of water. In the event of skin
contact, wash skin thoroughly with soap and water. Do not smoke during
application and use.
If swallowed seek immediate
medical advice and show the packaging or product label to the treating physician.
For
further instructions, cautions or notices, please refer to the product safety
data sheet. |
|
|
Protective Measures
|
|
The
general protective measures for water-soluble materials are to be considered.
The technical advice regarding the
use and application of our products is the result of extensive research and
development as well as many years of experience, and is given to the best of our
knowledge. The different kinds of requirements of an object/surface, under
varying conditions, make it necessary for the user to check the suitability for
the intended purpose. We reserve the right to effectuate changes which serve to
affect the technical advance or improvement of our product.
For further instructions, cautions
or notices, please refer to the product safety data sheet.
Dated:
02.04.2007 |
|
|
This product description is also available for download in PDF format: (click)
here! |
|
|
|
|
|
|
|
|
G PRO®
