NewPro-Bare Surface Graffiti Remover
(Only for Export)
-A Simple Graffiti Removal Solution on Unprotected Surfaces
For the German market we offer an alternative Graffiti Removal Blue!
Description
A
graffiti removal solution for application on open porous surfaces
which have not been coated with an Antigraffiti surface coating.
NewPro-Bare Surface Graffiti Remover was specially developed for the
removal of aerosol spray and marking pen graffiti, without leaving a
residual shadow. It is offered in gel form for easy application on
vertical surfaces.
Field/Range
of Application
NewPro-Bare
Surface Graffiti Remover was developed for the removal of Graffiti on
concrete, concrete and brick stone, but can be just as effective on
other surfaces.
Because
NewPro-Bare Surface Graffiti Remover contains an aggressive solvent,
it is not appropriate for use on pre-coated surfaces, or surfaces
which can be damaged by strong solvents.
When
in doubt regarding suitability, begin with a small test on the
surface or contact our service department. Our service department
will gladly advise you and offer you alternative products which are
more suitable for the intended use.
Product Characteristics
NewPro-Bare
Surface Graffiti Remover displays the following characteristics:
-
Suitable for airless spray (sprayable)
-
High Stability/Durability
-
High cleaning effectiveness
-
Short Curing Time
-
Easy Application
Technical Data
Ingredients:
-
Methanol, Methelene Chloride, Trichloroethylene.
For
further notices, instructions, or cautions, refer to the data safety
sheets for Graffiti Magic-Bare Surface Graffiti Remover.
Notice:
NewPro-Bare
Surface Graffiti Remover is specially designed for export. A private
or commercial application within the Federal Republic of Germany is
not permitted.
For
the German market, we offer an alternative Graffiti Removal Blue.
For
further notices, instructions, or cautions, refer to the data safety
sheets for Graffiti Removal Blue.
Procedural Instructions for Use
Surface Preparation:
All
surfaces must be dry and free from dirt and grime.
Use:
-
Apply a thick coat of NewPro-Bare Surface Graffiti Remover using a paintbrush, a brush or a spraying device directly onto the dirtied surface. - With surfaces which have extreme graffiti soiling, wait a few minutes and apply a second coating to strengthen cleaning power the first coating.
-
Subsequently, let the removal solution take effect for 10 to 30 minutes until the Graffiti reacts.
- Thoroughly rinse off the surface with clear water. - In the event that a shadow is left on the cleaned surface, let the surface completely dry and repeat steps 1-3.
Notice:
NewPro-Bare
Surface Graffiti Remover is not suitable for the removal of graffiti
from sensitive materials, plastics, Plexiglas or freshly coated or
painted surfaces.
When
in doubt regarding suitability, begin with a small test on the
surface or contact our service department. Our service department
will gladly advise you and offer you alternative products which are
more suitable for the intended use.
Machine/Mechanical
Application:
NewPro-Bare
Surface Graffiti Remover can be applied with a standard
airless/spraying device.
Notice:
NewPro-Bare
Surface Graffiti Remover is always to be applied undiluted.
NewPro-Bare
Surface Graffiti Remover is
not mixable with water or other chemicals. The
mixture with foreign substances completely neutralizes the cleaning
effect.
Cautionary
Notice:
While
opening the container, hold a towel or rag over the opening, to
minimize splashing, squirting or spraying of the product.
Wear the appropriate protective clothing and if necessary, a
breathing apparatus should be used.
Do
not allow NewPro-Bare Surface Graffiti Remover to dry on the cleaned
surfaces!
Application:
-
Approximately 0.5 m to 1.0 m per 1 Liter.
This
is simply a
recommended standard, which in end effect depends on the layer of
thickness as well as the absorbency of the surface area structure of
the surface.
An
exact amount of material needed can only be determined by a sample
coating on the surface of the object.
Required Conditions for Use/Application
The
application can be carried out with a surface area and air
temperature between min. +5°C and max. +30°C. NewPro-Bare
Surface Graffiti Remover is
not to be applied when temperatures exceed 25°C under direct
sunlight.
Required Conditions for Use
NewPro-Bare
Surface Graffiti Remover must only be applied in open air or in a
well-ventilated room.
The proper protective clothing should be worn and, if necessary, a
breathing apparatus should be used.
Notice:
During
the application of the product and curing time, the coated surface
must be protected from rain.
Curing
Time:
-
At an approximate temperature of 20°C, approximately 10 to 30 Minutes.
When
applying a second coating over intense graffiti soiling, the time may
increase. Wait until the product takes effect on the graffiti.
Time
is also influenced by the thickness of graffiti soiling.
Cleaning
of Tools:
-
Immediately after use, clean with water. If necessary, use solvents/cleaning solutions.
Form of Delivery
Units
Per Package:
-
5 Liter packages
Color
-
Colorless
Special Notices
Transportation:
-
Unlabeled and non-hazardous
Storage:
-
Cool, frost-free, in original closed package with a shelf life of approximately 1 year
Work Hygiene
Before
breaks and at the end working with the product, wash hands
thoroughly. Do not eat, drink or smoke during use. Avoid eye and
skin contact with the product. During use, wear protective gloves,
protective glasses and protective clothing, and if necessary,
breathing apparatus.
For
further instructions, notices, or cautions, refer to the product
safety data sheets.
Safety
Precautions
NewPro-Bare
Surface Graffiti Remover is not suitable for the removal of graffiti
from sensitive materials, plastics, Plexiglas or freshly coated or
painted surfaces. NewPro-Bare
Surface Graffiti Remover is
not mixable with water or other chemicals. The mixture with foreign
substances completely neutralizes the cleaning effect of the product.
For
further instructions, notices, or cautions, refer to the product
safety data sheets of NewPro-Bare
Surface Graffiti Remover.
Protective Measures
Keep
away from children. Keep containers sealed tightly closed. While
opening the container, hold a towel or rag over the opening. In the
event of eye contact, immediately flush eyes out with water In the
event of skin contact, wash skin thoroughly with water and soap. Do
not smoke during application and use. If swallowed seek immediate
medical advice and show the packaging or product label to the
treating physician.
The
technical advice regarding the use and application of our products is
the result of extensive research and development as well as many
years of experience, which results in the best knowledge. The
different kinds of requirements of an object, under varying
conditions, make it necessary for the user to check the suitability
for the intended purpose. We reserve the right to effectuate changes
which serve to affect the technical advance or improvement of our
product.
For
further instructions, notices, or cautions, refer to the product
safety data sheets.
